Samsung Washer Error Code LE: Leak Detected or Water Level Sensor Malfunction
$59 diagnostic β FREE with repair | 90-day warranty on parts & labor
What Our Customers Say
"I am so happy with the services provided by TruePro Home Services! I have a very old oven that I truly believed would need to be replaced. But, Yury came on time, diagnosed the issues, and had the parts with him to do the repair the same day. My oven is now in perfect working order. Highly recommend!"
Jill W.
Thousand Oaks
"Our LG Front Loading washer wasn't draining. I contacted Simon the next day. He had the part on his truck and came by within 30 minutes, and had it up and running super fast! Thank you Simon for your punctuality, honesty and great value. See you next time!"
Julia M.
Oxnard
"Wonderful and top notched care! They were able to meet my same day expectation to get a washer and dryer hooked up in a new house. He was attentive, thoughtful and explained it all as well. I would highly recommend their service!"
Aleema B.
Simi Valley
What Error Code LE Means
Your Samsung washer displays LE when the control board detects water where it should not be or receives abnormal readings from the water level pressure sensor. The washer stops the cycle immediately to prevent water damage. This code has two distinct causes: an actual water leak reaching the leak sensor on the base pan, or a faulty water level pressure sensor (pressure switch) sending incorrect data to the control board.
Common Causes
Leaking door boot seal
The rubber gasket around the front-load door opening develops tears, holes, or loosens from its retaining band. Water leaks past the seal during wash and drain cycles and drips into the base pan.
Loose or cracked drain hose connection
The drain hose connection at the pump or at the back of the machine is loose, or the hose itself has a crack. Water leaks during the drain phase.
Defective tub-to-pump boot
The rubber boot (short hose) connecting the outer tub to the drain pump develops holes or the hose clamps loosen. This is a common leak point on Samsung front-loaders.
Faulty water level pressure sensor
The pressure sensor (pressure switch) at the top of the washer connects to the tub via a small air hose. A cracked air hose, a clogged air dome, or a failed pressure switch causes erroneous readings that trigger LE without an actual leak.
Excess detergent causing suds overflow
Too much detergent or non-HE detergent creates excessive suds that overflow through vents or seals, dripping into the base pan and triggering the leak sensor.
How to Fix It
- 1
Look for visible water
Check the floor around and under the washer. Pull the machine forward and look behind it. If you see water on the floor, trace it to the source. Common leak points are the door seal, the drain hose connections at the back, and the detergent dispenser housing.
Unplug the washer before pulling it out or inspecting underneath. Wipe up standing water to prevent slipping.
- 2
Inspect the door boot seal
Open the door and run your hand around the entire rubber door gasket. Feel for tears, cuts, or areas where the rubber has pulled away from the front panel. Pull back the folds and look for mold, small holes, or degraded rubber. If the seal is damaged, it needs replacement.
- 3
Check drain hose connections
Inspect the drain hose at both ends: where it connects to the pump (bottom rear, accessed by removing the back panel) and where it enters the standpipe or connects to the sink drain. Tighten any loose hose clamps with a flathead screwdriver or a 5/16-inch nut driver. Replace the hose if it is cracked.
- 4
Inspect the tub-to-pump boot
Remove the front lower panel of the washer. The rubber boot connecting the tub to the drain pump is visible. Squeeze the boot and look for cracks, holes, or wet spots. Check the spring clamps on each end for proper tension. Replace the boot if it shows any damage.
- 5
Test the water level pressure sensor
Remove the washer's top panel (two Phillips screws at the rear). Locate the round pressure switch, usually mounted on the right side wall near the top. Trace the small clear air hose from the switch down to the tub. Check the hose for cracks, kinks, or disconnections. Blow gently into the hose -- you should hear a click from the switch. If the hose is cracked, replace it. If the switch does not click, replace the pressure switch.
Make sure the washer is unplugged before removing the top panel and testing the pressure switch.
- 6
Dry the base pan leak sensor
If you found and fixed the leak source, tilt the washer back carefully (with a helper) and use towels to dry the base pan and the leak sensor pad. The sensor is a small foam or plastic pad on the base. If it remains wet, the LE code will persist even after the leak is fixed. Let it air-dry completely before testing.
When to Call a Professional
Call a technician if you cannot locate the leak source, if the door boot seal needs replacement (it is a labor-intensive job), or if the pressure sensor tests bad. TruePro charges a $59 diagnostic fee credited toward the repair. We back all work with a 90-day warranty on parts and labor. Same-day service is often available. Call 877-378-3111 to schedule service in LA County, Orange County, or Ventura County. CA License #51112.
Estimated Repair Cost
| Option | Estimated Cost |
|---|---|
| DIY (parts only) | $10 - $95 |
| Professional repair | $175 - $425 |
A pressure hose costs $8-15. A pressure switch runs $25-40. A door boot seal costs $50-95 for the part alone. Professional repair includes the $59 diagnostic credit, parts, and labor. Use code NEW15 for 15% off labor on your first TruePro repair.
See full washer repair cost breakdown βSamsung Washer LE β FAQ
Related Samsung Error Codes
Ready to get your appliance fixed?
Book online in minutes or call for same-day availability.
90-day warranty β’ Upfront pricing β’ No hidden fees