Error Code EE
The EE error code means the EEPROM chip on the main control board cannot be read or written to. EEPROM stores your washer's operating parameters, cycle data, and calibration values. The washer cannot function without this data. This is a board-level failure, and the machine will not run any cycle until the board is repaired or replaced.
Common Causes
Corrupted EEPROM data: A power surge, brownout, or unstable voltage corrupts the data stored in the EEPROM chip. The washer cannot load its operating instructions.
Failed EEPROM chip: The physical chip on the control board has reached end of life or suffered electrical damage. It no longer retains data.
Main control board failure: The PCB traces or supporting components around the EEPROM chip have failed, preventing the processor from communicating with the memory.
Power surge damage: A lightning strike or utility power spike sent excess voltage through the board, frying the EEPROM and sometimes other components.
DIY Troubleshooting
Perform a hard reset: Unplug the washer from the wall outlet. Wait a full 5 minutes. This allows all capacitors on the control board to fully discharge. Plug the washer back in and attempt to start a cycle. If the EEPROM data was only temporarily corrupted, the board recovers during power-up.
Check for power supply issues: Plug the washer into a surge protector if it is plugged directly into the wall. Check your breaker panel for tripped breakers. Measure the outlet voltage with a multimeter — it should read between 110V and 125V AC. Unstable voltage corrupts EEPROM data.
Inspect the control board for visible damage: Unplug the washer. Remove the top panel and locate the main control board (usually housed in a plastic enclosure near the top-rear). Open the enclosure and inspect the board for burned components, blackened areas, swollen capacitors, or cracked solder joints. Visible damage confirms the board needs replacement.
Note your model number for parts ordering: The model number is on a sticker inside the door frame or on the back panel. You need this to order the exact replacement control board. LG control boards are model-specific.
Professional Repair
Call a technician for the EE error. Control board diagnosis and replacement involves handling sensitive electronics and matching firmware versions. TruePro technicians carry diagnostic tools to confirm the board failure before ordering parts. The $59 diagnostic fee is credited toward the repair, and all board replacements come with a 90-day warranty on parts and labor. CA License #51112. Call 877-378-3111 for same-day service in LA County, Orange County, or Ventura County. New customers get 15% off labor with code NEW15.
Need help with this error code?
Talk to a pro who's seen this code hundreds of times via video chat. Get a diagnosis, parts list, and fix-vs-replace advice in 15 minutes — online.
FAQ
What does LG error code EE mean?
The EE error code means the EEPROM chip on the main control board cannot be read or written to. EEPROM stores your washer's operating parameters, cycle data, and calibration values. The washer cannot function without this data. This is a board-level failure, and the machine will not run any cycle until the board is repaired or replaced.
Can I fix error code EE myself?
1. Perform a hard reset: Unplug the washer from the wall outlet. Wait a full 5 minutes. This allows all capacitors on the control board to fully discharge. Plug the washer back in and attempt to start a cycle. If the EEPROM data was only temporarily corrupted, the board recovers during power-up. 2. Check for power supply issues: Plug the washer into a surge protector if it is plugged directly into the wall. Check your breaker panel for tripped breakers. Measure the outlet voltage with a multimeter — it should read between 110V and 125V AC. Unstable voltage corrupts EEPROM data. 3. Inspect the control board for visible damage: Unplug the washer. Remove the top panel and locate the main control board (usually housed in a plastic enclosure near the top-rear). Open the enclosure and inspect the board for burned components, blackened areas, swollen capacitors, or cracked solder joints. Visible damage confirms the board needs replacement. 4. Note your model number for parts ordering: The model number is on a sticker inside the door frame or on the back panel. You need this to order the exact replacement control board. LG control boards are model-specific.
How much does it cost to fix error EE?
Typical repair costs: DIY: $100 - $250 | Pro: $250 - $475. Free diagnostic with approved repair.
Estimated Cost
DIY: $100 - $250 | Pro: $250 - $475
Free diagnostic with approved repair
Need Help With This Error?
Our technicians fix this error regularly. Same-day service available.
Call (877) 378-3111Virtual Diagnosis — $49